Thanks Thanks:  0
Likes Likes:  0
Results 1 to 8 of 8

Thread: RRD-8ANS & RRD-PRO Engraving

  1. #1

    RRD-8ANS & RRD-PRO Engraving

    Does anyone have any options for RRD-8ANS & RRD-PRO engraving? I finished installing >30 switches and have many 2-, 3-, and 4-gang locations. It would be nice to be able to engrave these.

  2. #2
    Quote Originally Posted by radioRA2automation View Post
    Does anyone have any options for RRD-8ANS & RRD-PRO engraving? I finished installing >30 switches and have many 2-, 3-, and 4-gang locations. It would be nice to be able to engrave these.
    https://laserengraverpro.com/brands/lutron/

  3. #3
    Senior Member
    Join Date
    Oct 2013
    Posts
    2,587
    Quote Originally Posted by Imshea View Post
    Lutron will engrave Lutron brand 2-part plates (i.e. claro, nova T, etc.).
    Convergence Technologies Raleigh, North Carolina
    www.convergenceusa.com

  4. #4
    Quote Originally Posted by randyc View Post
    Lutron will engrave Lutron brand 2-part plates (i.e. claro, nova T, etc.).
    I have RRD-8ANS and RRD-PRO. I need the actual switch engraved, not the wall plate. Surprised this is not available or perhaps there was no demand. Seems they could use the same machine as they use for the keypad buttons.

  5. #5
    Senior Member
    Join Date
    Oct 2013
    Posts
    2,587
    Quote Originally Posted by radioRA2automation View Post
    I have RRD-8ANS and RRD-PRO. I need the actual switch engraved, not the wall plate. Surprised this is not available or perhaps there was no demand. Seems they could use the same machine as they use for the keypad buttons.
    Lutron will probably engrave the buttons. It's going to be a custom thing and you would probably have to order new button kits.

    Any local engraver should be able to do it. It's curved surfaces (like seeTouch buttons) they have problems with.
    Convergence Technologies Raleigh, North Carolina
    www.convergenceusa.com

  6. #6
    I'll give them a call, however, I asked a local engraver to give it a shot on some spare switch covers. The company tried laser engraving and it melted the plastic and turned it yellow. They do not have a laser etching machine and cannot try that. I assume Lutron uses silk screening or some type of laser etching.

  7. #7
    Senior Member
    Join Date
    Jun 2013
    Posts
    1,365
    Try emailing my buddy- traviselectronics@gmail.com. He engraves keypads well, and I have a 4 button Pico he tested- no issues at all.
    Simple automation when DIY isn't working
    intuitivehomecontrols@gmail.com
    fb.me/intuitivehomecontrols

  8. #8
    Thanks for that!

Similar Threads

  1. RRD-8ANS not registering
    By dougpark464 in forum Troubleshooting - RA2
    Replies: 2
    Last Post: 10-21-2019, 03:45 PM
  2. RRD-8ANS - Not Registering
    By 2k15Ducati in forum Programming - RA2
    Replies: 2
    Last Post: 11-17-2018, 10:46 AM
  3. RRD-8ANS - Cannot Find in Software
    By Shandley in forum Programming - RA2
    Replies: 3
    Last Post: 02-16-2018, 10:04 PM
  4. issue with CFL lights and rrd-8ans
    By trx250r87 in forum Troubleshooting - RA2
    Replies: 3
    Last Post: 08-15-2014, 04:46 PM
  5. 8ANS without a neutral
    By Craig W. in forum General Discussion - HWQS
    Replies: 0
    Last Post: 01-20-2014, 06:58 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •