Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 3 of 3

Thread: Where is the HWQS monitoring output?

  1. #1
    Junior Member
    Join Date
    Aug 2018
    Posts
    7

    Where is the HWQS monitoring output?

    I just had a HWQS system installed and I turned on event monitoring via telnet so I could find the integration IDs for all my components. Where is the output of the monitoring? Events don't appear to be displaying in my telnet session when I change dimming on some lights. Here's the session showing the event monitoring setting:

    QNET> #MONITORING,2,1
    ~MONITORING,2,1
    QNET> ?MONITORING,255
    ~MONITORING,1,2
    ~MONITORING,2,1
    ~MONITORING,3,2
    ~MONITORING,4,2
    ~MONITORING,5,2
    ~MONITORING,6,2
    ~MONITORING,7,2
    ~MONITORING,8,2
    ~MONITORING,9,2
    ~MONITORING,10,2
    ~MONITORING,11,1
    ~MONITORING,12,1
    ~MONITORING,13,2
    ~MONITORING,14,2
    ~MONITORING,16,2
    ~MONITORING,17,2
    ~MONITORING,18,2
    ~MONITORING,19,2
    ~MONITORING,20,2
    ~MONITORING,21,2
    ~MONITORING,22,2
    ~MONITORING,23,2
    ~MONITORING,24,2
    ~MONITORING,25,2
    ~MONITORING,26,2
    ~MONITORING,27,2

  2. #2
    Junior Member
    Join Date
    Aug 2018
    Posts
    7
    Ok, I turned on some more monitors and I'm getting some output in my telnet session, but the event monitoring output does not show the integration id of the device associated with the event.

    Also, where is the documentation on the messages from the monitoring? For example, I see a "GLINK_INFO_DUMP for HWQS-KEYPAD-DOM2 Object ID 00000400" message. Without output documentation, I'm not clear on what that message means.

  3. #3
    Authorized Lutron Contributor
    Join Date
    Apr 2013
    Posts
    403
    The integration protocol guide can be found at http://www.lutron.com/TechnicalDocum...ary/040249.pdf. As for the "GLINK_INFO_DUMP for HWQS-KEYPAD-DOM2 Object ID 00000400" message this is not used for integration. This message indicates the the devices was sent information from the processor.

Similar Threads

  1. Seriously? Is no one monitoring these forums at all?
    By AndyM in forum General Discussion - HWQS
    Replies: 2
    Last Post: 04-19-2018, 12:35 PM
  2. QSE-CI-NWK-E OUTPUT command
    By deustis in forum Programming - HWQS
    Replies: 1
    Last Post: 09-07-2017, 09:58 AM
  3. CCO and WPM output on HOME+ App
    By diogomoreira in forum General Discussion - Legacy HW
    Replies: 1
    Last Post: 05-25-2017, 02:54 PM
  4. VCRX Output gone from Connect App once set pulsed
    By dvpvic in forum Programming - RA2
    Replies: 5
    Last Post: 05-24-2017, 09:47 AM
  5. Define an Output on a Dimming Module as On/Off Only?
    By David Haddad in forum Programming - HWQS
    Replies: 2
    Last Post: 11-07-2013, 10:39 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •