Thanks Thanks:  1
Likes Likes:  1
Dislikes Dislikes:  0
Results 1 to 4 of 4

Thread: Switch off motion sensor if curtain is not fully open

  1. #1
    Junior Member
    Join Date
    Mar 2016
    Posts
    15

    Switch off motion sensor if curtain is not fully open

    Hi to everyone,
    I have a problem with conditional programming.
    There is an automatic sliding door with a passive infrared sensor.
    In front of the sliding door is curtain.
    I shall switch off the passive infrared sensor for the automatic sliding door (via cco) if the curtain is not fully open.

    Any ideas how to do this with conditional programming?

    Cheers
    Frank

  2. #2
    Senior Member
    Join Date
    Oct 2013
    Posts
    2,587
    None of the devices you listed have built-in timers. To edit a system timed event, you will need the RR2 software & database OR the Home Control+ app OR the Lutron Connect app.

    With HC+. select any room, tap the "Events" icon, select the event and tap "EDIT" in the upper right corner. Similar procedure for Connect app.

    Events are assigned to specific time clock modes. Vacation lights might be assigned to "Away." Exterior lights might be assigned to "Away" and "Normal." To check/change the mode you will need HC+ on a tablet to the Connect app.
    Convergence Technologies Raleigh, North Carolina
    www.convergenceusa.com

  3. #3
    Junior Member
    Join Date
    Mar 2016
    Posts
    15
    Thank you for your reply, but I do not understand why you are talking about timed events. There is no timing for the event. It is just to match somehow if the curtain is in the open limit position or not. The logic how to do this is not the problem. But you can only assign logics in conditional programming for a button. And the button is the trigger for the logic. It would be very cool to create logics like timers in HWQS. I do not have a solution to trigger a logic every time the curtain will be moved by open/stop/close/stop.

  4. #4
    Senior Member
    Join Date
    Oct 2013
    Posts
    2,587
    Too many windows open. Sorry.

    This conditional says, if the curtain is "open" close the CCO (enable PIR sensor), if the curtain is "not open" open the CCO (disable the PIR sensor).

    HW Illumination had some pre-programmed sequences like Open/stop/close/stop for shades and fan speed control. They are probably coming for HQS but who knows when??


    Click image for larger version. 

Name:	Contitional.jpg 
Views:	13 
Size:	107.1 KB 
ID:	789
    Convergence Technologies Raleigh, North Carolina
    www.convergenceusa.com

  5. Thanks Blair S. thanked for this post
    Likes Blair S. liked this post

Similar Threads

  1. Dimmer Switch on Security Light with Motion Sensor?
    By ApolloX in forum General Discussion - CAS
    Replies: 1
    Last Post: 04-05-2018, 09:34 PM
  2. Need advice for motion sensor
    By mestregroda in forum General Discussion - Controls
    Replies: 1
    Last Post: 06-20-2017, 11:35 AM
  3. Timer switch paired with remote motion sensor
    By Lukeetal in forum Design Assistance - Controls
    Replies: 1
    Last Post: 09-27-2016, 08:55 PM
  4. Motion sensor question, some on & more off?
    By wkearney99 in forum Programming - RA2
    Replies: 4
    Last Post: 03-05-2015, 07:59 AM
  5. Motion sensor Overide
    By mdfeather in forum Programming - RA2
    Replies: 2
    Last Post: 11-17-2013, 07:37 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •