Thanks Thanks:  0
Likes Likes:  1
Dislikes Dislikes:  0
Results 1 to 2 of 2

Thread: Advanced Timeclock Troubleshooting

  1. #1
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    513

    Advanced Timeclock Troubleshooting

    A dealer had asked us for specific timeclock testing commands for the HomeWorks QS software terminal and we thought the information would be useful to share in the forum. Please be aware most if not all these commands can be found on the Lutron Commands menu at the bottom of the terminal screen.

    Testing Timeclock in Terminal

    • At any point, you may type in the command "??" to view a list of available commands. To review a description of the command, type in commands on the format: "?help,command" for example: "?help,?timeclock". To review the specific command action, you can send a command in the format: "?help,command,action number". For example: "?help,?timeclock,1"

    • The command "gettime" will display the current system time

    • The command "settime" will set the system time. Please use format "settime,hh,mm,ss"

    • The command "getdate" will show the current date. The command "setdate" will allow you to change the current date. Please use format "setdate,mm,dd,yy"

    • Type in the command "getsunrise" to see the time the system is supposed to go on to sunrise for that specific day

    • Type in the command "getsunset" to see the time the system is supposed to go on to sunset for that specific day

    • To test the timeclock, we will need to know the ID of the project timeclock. You may find it in Tools->Configure Integration->IDs tab-> Project Time Clock and note the ID of the timeclock. You may also get this information from the integration report

    • Type in the command "?timeclock,<ID>,4" and it will tell you the timeclock events scheduled for that day as well as the time they are scheduled.

    • Type in the command "#timeclock,<ID>,5,<event index>, to execute a timeclock event. Please be aware, the event index is the index in order of how the events were created.

    Example of Advanced Troubleshooting:
    Send a getsunset command, then set the time of the timeclock 10 seconds before sunset to see if the timeclock happens as it should using the settime command. For example, if the sunset happens at 20:08 (8:08pm), do this command: "settime,20,07,50" and will set the time to 8:07:50pm. After 10 seconds, it will be sunset; you may use the "gettime" command to double check. If the timeclock occurs, it should be working fine. If it does not, there is something wrong.

  2. Likes Blair S. liked this post
  3. #2
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    513
    UPDATE:

    When sending the command "?timeclock,<ID>,4"

    All timeclock events possible for the day will be listed. Including those that are disabled and Vacation mode events (even if vacation mode is disabled).

    In order to best determine if a specific project timeclock is enabled or disabled, please follow the steps in the post below:

    https://forums.lutron.com/showthread...ced+timeclocks

Similar Threads

  1. Fixing Normal Timeclock Modes Getting Randomized in Away
    By schalliol in forum General Discussion - RA2
    Replies: 6
    Last Post: 05-16-2017, 12:23 AM
  2. Control Timeclock Events with Keypad Button Presses
    By Armando B. in forum Programming - Legacy HW
    Replies: 0
    Last Post: 01-02-2014, 03:54 PM
  3. Timeclock question
    By EUCOMM in forum Programming - HWQS
    Replies: 4
    Last Post: 11-22-2013, 01:07 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •