Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 7 of 7

Thread: IR Commands

  1. #1
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    513

    IR Commands

    We had a question from a dealer about IR compatibility in HomeWorks QS. We thought the following information was useful to share with the forum community:

    The wired HQWD-W5BIR keypad and the Grafik Eye QS will have a programmable IR sensor in them.

    In the program tab of the software, you can select those devices and there will be an additional probrammable IR tab. In it you will see the command the IR device would need to send, the name given to that command, and the input number (consider it a button number for integration purposes) for that command.

  2. #2
    Can the QSE-IR-WH be used with HomeWorks QS wired to the QS Link? It doesn't seem to be in the Tool Box. Does it have a serial number on it? With HW Illumination we had a few options to use for IR (CCI-8 etc). It would be nice to have a low-cost IR receiver which could be installed at an A/V equipment rack.

  3. #3
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    513
    Unfortunately the QSE-IR is not available for the HomeWorks QS system. Thank you for this feedback.

  4. #4
    Junior Member
    Join Date
    Feb 2015
    Posts
    3
    Quote Originally Posted by Armando B. View Post
    We had a question from a dealer about IR compatibility in HomeWorks QS. We thought the following information was useful to share with the forum community:

    The wired HQWD-W5BIR keypad and the Grafik Eye QS will have a programmable IR sensor in them.

    In the program tab of the software, you can select those devices and there will be an additional probrammable IR tab. In it you will see the command the IR device would need to send, the name given to that command, and the input number (consider it a button number for integration purposes) for that command.
    Sorry to pull up an old thread, but how do the IR commands correlate with the keypad buttons on the seeTouch keypads that have IR receivers?

  5. #5
    Authorized Lutron Contributor
    Join Date
    Jun 2013
    Posts
    91
    The IR commands would be programmed seperately from the buttons on a 5 button IR keypad or a GrafikQS unit. think of it as a seperate 8 scene + off keypad. Select the keypad and click on the IR tab in programming to see the exact commands.

  6. #6
    Junior Member
    Join Date
    Feb 2015
    Posts
    3
    Quote Originally Posted by Tim S. View Post
    The IR commands would be programmed seperately from the buttons on a 5 button IR keypad or a GrafikQS unit. think of it as a seperate 8 scene + off keypad. Select the keypad and click on the IR tab in programming to see the exact commands.
    Tim, Thanks for your response. Can you point me to what software I would use to program it?

  7. #7
    Authorized Lutron Contributor
    Join Date
    Jun 2013
    Posts
    91
    This application would be for the Homeworks QS system. If you have a stand-alone QS Shade application with an IR keypad, the IR commands would mimic the keypad button commands.

Similar Threads

  1. How do I send out commands?
    By Kevin P. in forum 3rd-party Integration - RA2
    Replies: 13
    Last Post: 03-25-2016, 04:59 PM
  2. Commands getting missed?
    By amyriley in forum Troubleshooting - RA2
    Replies: 3
    Last Post: 12-11-2013, 12:25 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •