Thanks Thanks:  0
Likes Likes:  0
Page 2 of 2 FirstFirst 12
Results 11 to 16 of 16

Thread: Fireplace Control w/2 wire

  1. #11
    Quote Originally Posted by gt3mike View Post
    I haven't done it yet, but I'm planning to do it with an RRD-8ANS and one of these relays: https://www.functionaldevices.com/pr...etails/RIBU1C/
    Did you do this? If so how did you make this work from the switch to the relay?

  2. #12
    Senior Member
    Join Date
    Jul 2015
    Posts
    214
    Quote Originally Posted by audiowizardJ View Post
    Did you do this? If so how did you make this work from the switch to the relay?
    I actually ended up using one of the contact closures on a VCRX. Worked perfectly.

  3. #13
    Junior Member
    Join Date
    Jul 2016
    Posts
    12
    Quote Originally Posted by gt3mike View Post
    I actually ended up using one of the contact closures on a VCRX. Worked perfectly.
    Has anyone done this with a relax? If so, do you have a diagram? I never got around doing mine and need to change the switch given everything I have is RadioRa2 but this bank of switches.

  4. #14
    Junior Member
    Join Date
    Jul 2016
    Posts
    12
    I meant Relay? And if so, a diagram of the switch, relax and wires. Thanks!

  5. #15
    Authorized Lutron Contributor
    Join Date
    Sep 2021
    Posts
    19
    Lutron would recommend the LMJ-CCO1-24-B or the RR-VCRX-WH as a contact closure for Radio RA2. We've included the spec sheets of each device below:
    https://www.lutron.com/TechnicalDocu...369224_ENG.pdf
    https://www.lutron.com/TechnicalDocu...369770_ENG.pdf

    hope this helps guide you in the right direction.

  6. #16
    Quote Originally Posted by BigOil View Post
    I for one, not expecting Lutron help on this one as it gets to code issues and liability.
    Lutron provides 120V switching or dimming. Not relays.
    Or in this case, the LMJ-CCO1-24-B is the correct part and Lutron provides a CCO.

    In my opinion, really up to appliance OEM to provide guidance on how they advice interfacing on/off 24V to a 120V switch.
    Or it's up to trades or a PE to designate a workaround using the CCO.
    Lutron RF Relay Module is available however not sure it would work with this installation.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Fireplace Motor Control
    By heimdm in forum General Discussion - RA2
    Replies: 2
    Last Post: 02-22-2018, 11:05 PM
  2. Fireplace Blower Control
    By heimdm in forum Design Assistance - RA2
    Replies: 2
    Last Post: 12-31-2017, 05:23 PM
  3. Fireplace control?
    By lantzpantz in forum General Discussion - CAS
    Replies: 3
    Last Post: 01-11-2016, 12:15 PM
  4. Fireplace Control
    By Staker in forum Design Assistance - RA2
    Replies: 10
    Last Post: 12-31-2014, 05:08 PM
  5. 8ANS for low voltage fireplace control?
    By dw886 in forum Design Assistance - RA2
    Replies: 4
    Last Post: 04-20-2014, 03:52 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •