Thanks Thanks:  1
Likes Likes:  0
Page 2 of 2 FirstFirst 12
Results 11 to 13 of 13

Thread: Anyone else having to replace Lutron switches with broken bezels that won't stay on?

  1. #11
    Junior Member
    Join Date
    Apr 2019
    Posts
    3
    Mike, S.

    Attached is my Lutron Diva switches that are no longer being used because of broken switch rocker paddles. All switches are good but I had to replace at the cost of a new switch because the light would not stay on due to the broken paddle. Will Lutron take warrant this defective Click image for larger version. 

Name:	IMG_6502.JPG 
Views:	5 
Size:	154.0 KB 
ID:	867Click image for larger version. 

Name:	IMG_6505.JPG 
Views:	6 
Size:	88.4 KB 
ID:	868Click image for larger version. 

Name:	IMG_6507.JPG 
Views:	6 
Size:	89.3 KB 
ID:	869Click image for larger version. 

Name:	IMG_6508.JPG 
Views:	5 
Size:	88.9 KB 
ID:	870Click image for larger version. 

Name:	IMG_6509.JPG 
Views:	5 
Size:	94.3 KB 
ID:	871problem?

  2. #12
    Junior Member
    Join Date
    Apr 2019
    Posts
    3
    Hi Mike,Attached is my Lutron switches that are no longer being used because of broken switch rocker paddles. All switches are good but I had to replace all at the cost of new switches because the light would not stay on due to the plastic paddle being broken as others have stated in this forum. 6 Diva 600Ps, 1 Diva 603P and 1DV10P. Cost me approximately $250 plus my time to purchase and install. This does not include the time we had no lights or limited use of our lights while the switches were unusable. Will Lutron take care of this problem?????

    Click image for larger version. 

Name:	IMG_6502.JPG 
Views:	3 
Size:	154.0 KB 
ID:	872Click image for larger version. 

Name:	IMG_6505.JPG 
Views:	2 
Size:	88.4 KB 
ID:	873Click image for larger version. 

Name:	IMG_6508.JPG 
Views:	3 
Size:	88.9 KB 
ID:	874Click image for larger version. 

Name:	IMG_6509.JPG 
Views:	3 
Size:	94.3 KB 
ID:	875

  3. #13
    Senior Member
    Join Date
    Oct 2013
    Posts
    177
    I run into this quite often. Fortunately being an electrical company we have a lot of old Diva's we take out for various reasons. We keep all the old face plates just for this reason. Been told Lutron can't sell the face plate because it's not URL approved. I have never talked directly with Lutron about this just been told from two different sources they have been told direct from Lutron. But they sell the Maestro face plate.? Maybe call a local electrician and see if they could sell a few. Cheaper than buying the whole device.
    Usually break down with age not over use but will say I have a house that requires frequent changes kits. Former Football player. Always in his bath.

Page 2 of 2 FirstFirst 12

Similar Threads

  1. Need to replace two QED in system.
    By swmiller2@gmail.com in forum Troubleshooting - Legacy HW
    Replies: 2
    Last Post: 02-15-2018, 01:33 PM
  2. Will the New AppleTV replace the Lutron CasÚta Smart Bridge?
    By rodrakic in forum 3rd-party Integration - CAS
    Replies: 1
    Last Post: 10-19-2015, 04:11 PM
  3. Essentials/Exclusive 9.0 Broken for XP
    By schalliol in forum General Discussion - RA2
    Replies: 3
    Last Post: 06-01-2015, 10:02 AM
  4. C4 controller with Lutron light switches/dimmers?
    By alexb in forum General Discussion - HWQS
    Replies: 2
    Last Post: 05-21-2015, 09:36 AM
  5. RA1 homeower wanting to replace with RA2 questions
    By terryreid in forum General Discussion - RA2
    Replies: 1
    Last Post: 09-10-2014, 10:04 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •