Thanks Thanks:  1
Likes Likes:  2
Dislikes Dislikes:  0
Page 4 of 4 FirstFirst ... 234
Results 31 to 35 of 35

Thread: Anyone else having to replace Lutron switches with broken bezels that won't stay on?

  1. #31
    Senior Member
    Join Date
    Oct 2013
    Posts
    518
    Quote Originally Posted by ProfBernie View Post
    I, too, have this problem; two broken bevels on rocker dimmer switches.
    No one makes switches that are immune to abuse.

  2. #32
    Junior Member
    Join Date
    Jul 2022
    Posts
    3
    I HAVE A FIX THAT ABSOLUTELY WORKS! I POSTED THE PROCEDURE IN DETAIL. ESSENTIALLY, IT'S CREATING AN "AXIS" FOR THE PADDLE TO SWING ON. See details in my post above -- Dr. Air, dated 7/19/22.

  3. #33

    Same Problem

    5 switches have gone bad all in the last 6 months!
    Last edited by uAintThatTall; 05-15-2023 at 04:35 AM. Reason: Wrong thread

  4. #34
    Junior Member
    Join Date
    Jul 2022
    Posts
    3
    Responding to uAintThatTall.
    I received an email from Lutron Support that showed the above post today. Do you have a question?
    I'm not good at navigating or interacting with this forum. Feel free to email me at wheeoo@cox.net.
    I do have a fix for the rocker switch which is simple and will last forever.
    Stan (aka Dr. Air)

  5. #35
    Junior Member
    Join Date
    Jul 2023
    Posts
    1
    This post has been very helpful. I was able to carefully take the rocker switch off the switch assembly without unscrewing anything or having to disconnect the wires. It's easy to pry it off but the spring and spring assembly may fall off. I replaced the spring and assembly on the back of the rocker switch and taped a very thin piece of plastic (as described by n1oconnor earlier in this thread) to the outside of the small plastic "box" that holds the spring in place. I taped it on the same side as the broken bevel on the back of the switch plate. Gently snapped it back in place and everything works! The rocking action isn't as smooth as before but it works and is better than replacing the entire switch assembly because one tiny piece of plastic broke off the back of the switch plate. It's ridiculous that Lutron doesn't sell replacement rocker switch plates. It has to be about a $.10 piece of plastic.

Page 4 of 4 FirstFirst ... 234

Similar Threads

  1. Need to replace two QED in system.
    By swmiller2@gmail.com in forum Troubleshooting - Legacy HW
    Replies: 2
    Last Post: 02-15-2018, 01:33 PM
  2. Will the New AppleTV replace the Lutron Caséta Smart Bridge?
    By rodrakic in forum 3rd-party Integration - CAS
    Replies: 1
    Last Post: 10-19-2015, 04:11 PM
  3. Essentials/Exclusive 9.0 Broken for XP
    By schalliol in forum General Discussion - RA2
    Replies: 3
    Last Post: 06-01-2015, 10:02 AM
  4. C4 controller with Lutron light switches/dimmers?
    By alexb in forum General Discussion - HWQS
    Replies: 2
    Last Post: 05-21-2015, 09:36 AM
  5. RA1 homeower wanting to replace with RA2 questions
    By terryreid in forum General Discussion - RA2
    Replies: 1
    Last Post: 09-10-2014, 10:04 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •