Thanks Thanks:  0
Likes Likes:  0
Results 1 to 5 of 5

Thread: PD-6ANS Multi-Location (3 physical switches) Install Issue - Lights won't turn off

  1. #1
    Junior Member
    Join Date
    Jan 2018
    Posts
    2

    PD-6ANS Multi-Location (3 physical switches) Install Issue - Lights won't turn off

    Second time installing a PD-6ANS switch (first time was a simple single pole install), this time for a 4 way setup (3 physical switches, 2x3-way and 1x4-way). Townhouse built in 2008, neutrals in every j-box.

    Here's the LED chandelier (same model used on my prior PD-6ANS install, no issues then):

    https://www.homedepot.com/p/Home-Dec...7584/206058643

    Followed the multi-room + 2 Pico instructions on p. 46 of this doc:

    http://www.casetawireless.com/Docume...ced%20Inst.pdf

    Installed the PD-6ANS in Location 1 (3-way), then connected/capped all 4 wires and separately capped the ground at Location 2 (4-way), then connected/capped all 3 wires and separately capped the ground at Location 3 (3-way). Triple checked all wiring looked good, then re-did it all to prove my sanity.

    When I flip the breaker back on, the light comes on, but the switch thinks the light is off (the PD-6ANS buttons do nothing, but the LED status light is dim green, implying the light is off). Can't turn the light off, either from the PD-6ANS or the paired Picos. Pulling out FASS does nothing, so obviously something is terribly wrong....it's like the light is hard-wired. Only way to turn the light off is hitting the breaker (leaving the breaker off, obviously).

    Help? Couldn't find anything on the web addressing this issue. Can't figure out if this is a switch hardware issue or my wiring skills. No multimeter or any testing equipment on hand.

  2. #2
    Senior Member
    Join Date
    Jun 2013
    Posts
    1,363
    See the note on page 50. Probably have the line in (on the left of the dimmer in the diagram) swapped with one of the loads out (travelers in your diagram). Get a glow stick to check if you don't have one- best $10-20 you'll spend if you are trying to do this yourself.
    Simple automation when DIY isn't working
    intuitivehomecontrols@gmail.com
    fb.me/intuitivehomecontrols

  3. #3
    Junior Member
    Join Date
    Jan 2018
    Posts
    2
    Mike, thanks for replying. I flipped things and ended up with no light (and no dim LED status light). Of the 3 wires in play (1 hot + 2 travelers), no combo would work....either light always on or no power. I fear I may have fried the switch....I'm going to test it in a simpler single pole setup to be sure.

  4. #4
    Senior Member
    Join Date
    Jun 2013
    Posts
    1,363
    I would go to Lutron's where to buy at the top of lutron.com. Look for someone who does RadioRA2 or HomeWorks and have them come take a look. Most electricians are pretty cool and will explain what they are doing, if you aren't hovering over their work. It will cost you a bit, but knowledge is valuable. If you learn for yourself, then you can save on the next install.
    Simple automation when DIY isn't working
    intuitivehomecontrols@gmail.com
    fb.me/intuitivehomecontrols

  5. #5
    Junior Member
    Join Date
    Sep 2020
    Posts
    3
    I know this is an old thread but I have the exact same issue. Triple checked everything, depending on where I have the black/red wire in Location 1 the lights are either always on or always off. Did you ever find a resolution?Thanks

Similar Threads

  1. Model number with -R at the end of Multi-location In wall switch
    By cuckooc in forum General Discussion - CAS
    Replies: 1
    Last Post: 12-17-2017, 10:02 AM
  2. Pico Dimmer Switch and Smart Switch in a multi-location setup
    By jbaude in forum General Discussion - CAS
    Replies: 1
    Last Post: 11-08-2017, 04:06 PM
  3. Grafik T Multi Location Dimmer doesn't work
    By modkris in forum Troubleshooting - Controls
    Replies: 3
    Last Post: 02-14-2017, 04:01 PM
  4. Caseta Wireless 600-watt/150-watt Multi-Location In-Wall Dimmer
    By calirap in forum General Discussion - CAS
    Replies: 1
    Last Post: 01-06-2016, 09:19 AM
  5. Strange Issues on Multi-Location Dimmers
    By schalliol in forum Troubleshooting - RA2
    Replies: 5
    Last Post: 05-13-2015, 06:59 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •