Thanks Thanks:  0
Likes Likes:  0
Results 1 to 7 of 7

Thread: Caseta Switch only turns light on after FASS reset

  1. #1
    Junior Member
    Join Date
    Oct 2017
    Posts
    2

    Caseta Switch only turns light on after FASS reset

    Caseta switch model pd-6ans-wh seems to be working correctly, but lights only turn on if I pull out the FASS tab, press the ON button, and close the tab again. Once the lights have been turned off, they won't turn on again without repeating the FASS reset procedure. Called lutron cs and was sent a lut-mlc device. No change. Ideas?

  2. #2
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    540
    What kind of lights? Incandescent? Halogen? LED?
    How many watts total?

  3. #3
    Junior Member
    Join Date
    Oct 2017
    Posts
    2
    Quote Originally Posted by Brian W. View Post
    What kind of lights? Incandescent? Halogen? LED?
    How many watts total?
    360 watts of halogen

  4. #4
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    540
    Where did you install the LUT-MLC? At the light or in the switchbox?
    Did you conenct one lead to the neutral, and the other lead to the switched-hot wire coming from PD-6ANS?
    Do you have the neutral connected to the white wire on the PD-6ANS?

  5. #5
    Junior Member
    Join Date
    Dec 2017
    Posts
    4
    Quote Originally Posted by Kjkpilot View Post
    Caseta switch model pd-6ans-wh seems to be working correctly, but lights only turn on if I pull out the FASS tab, press the ON button, and close the tab again. Once the lights have been turned off, they won't turn on again without repeating the FASS reset procedure. Called lutron cs and was sent a lut-mlc device. No change. Ideas?

    Did you find a solution to this? I'm having the exact same problem, trying to control my outdoor porch light with an interior switch.

    I connected the ground, the two black wires from the wall to what I thought were the correct corresponding hot and load wires, and then the neutral to a white wire inside the switch box.

    The white wire was not connected to anything, it was just in the box, so maybe that isn't a neutral?

  6. #6
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    540
    Kjkpilot: did you try reversing the black and red wires on the PD-6ANS?

    Kiechhafer: Was the white wire connected to another white wire, or was it not connected to anything at all?

  7. #7
    Junior Member
    Join Date
    Dec 2017
    Posts
    4
    Quote Originally Posted by Brian W. View Post
    Kjkpilot: did you try reversing the black and red wires on the PD-6ANS?

    Kiechhafer: Was the white wire connected to another white wire, or was it not connected to anything at all?
    I actually ended up getting it fixed by reversing the wires. Bought a tester and realized the load and hot were backwards.

    Thanks!

Similar Threads

  1. MS-OPS2 manually turns on and off LED light, but doesn't allow programming
    By mbeckham in forum Troubleshooting - Controls
    Replies: 1
    Last Post: 10-11-2017, 11:33 AM
  2. Caseta Dimmer Switch - Flickering LED Light
    By OmerNisar in forum Troubleshooting - CAS
    Replies: 8
    Last Post: 04-20-2017, 04:37 PM
  3. MA-LFQHW light swtich turns on fan on full brightness
    By teepee1232 in forum General Discussion - Controls
    Replies: 2
    Last Post: 10-09-2016, 10:14 AM
  4. Replies: 1
    Last Post: 09-01-2015, 12:24 AM
  5. Caseta offer fan/light switch combo like maestro?
    By chachdog in forum General Discussion - CAS
    Replies: 2
    Last Post: 06-11-2015, 10:45 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •