Thanks Thanks:  1
Likes Likes:  0
Results 1 to 3 of 3

Thread: Combining Pico Keypad with HomeWorks QSX

  1. #1
    Junior Member
    Join Date
    Sep 2023
    Posts
    2

    Combining Pico Keypad with HomeWorks QSX

    Hello Community,

    I am currently in discussion with a local Lutron dealer for an upcoming HomeWorks QSX retrofit of my 75sqm (~800sqft) apartment. I am mainly going to have Palladiom keypads installed in the different rooms, however, I would like to realize the following scenario which I would like to briefly describe, including the suggestion from the dealer, but I ideally would like to get a confirmation here from you.

    So, my bedroom has a custom-made headboard affixed to the outer wall of my condominium apartment. There is a LED light strip on top of the headboard which is currently connected to a 'dumb', third-party dimmer/switch.

    I have attached here the lighting design for my retrofit project. Due to space/storage constraints in my apartment, we cannot fit everything into a cabinet. Hence, we assign the necessary hardware into three different service panels located above the false/low-hanging ceiling. Only the 'core' components e.g. processor etc. go into a kitchen cabinet.

    The Lutron dealer suggested that the LED light strip (number 11 on the attached diagram) needs to be hardwired to the nearest service panel - is that correct? Maybe I have a wrong understanding but I was under the assumption that the LED strip is connected to the actual Pico keypad (KP8) which then connects to the wireless module (QSM1)?

    Click image for larger version. 

Name:	Screenshot 2023-09-16 at 11.25.47 AM.jpg 
Views:	5 
Size:	536.9 KB 
ID:	1054Click image for larger version. 

Name:	Screenshot 2023-09-16 at 11.30.55 AM.png 
Views:	5 
Size:	210.9 KB 
ID:	1053

    The overall challenge with the headboard is that it is affixed to the outer wall which I am not allowed to cut into. Also, the headboard base is made of a high-quality wood and a nice fabric which I am not eager to drill into to somehow be able to run wires from the LED to the service panel.

    Any suggestions/advice on this topic or even the overall suggested design is appreciated.

    With Regards,
    SamboSoul

  2. #2
    Senior Member
    Join Date
    Sep 2014
    Posts
    267
    A Pico is not a dimmer- it is only a keypad- it cannot control the lighting load on its own. You need a dimmer hooked up to your lights in order to be able to control it from the Pico. So you would tie it to your 4A5 module as an output and then it would be controllable from the Pico.

  3. Thanks SamboSoul thanked for this post
  4. #3
    Junior Member
    Join Date
    Sep 2023
    Posts
    2
    Appreciate your feedback johnmax.

    I did some more research and I was told that I could use a hybrid repeater in conjunction with a in-line dimmer connected to the LED light strip, is that correct? That way I could use the Pico keypad for the dimming and without having to pull a wire from LED light strip to the nearest service panel.
    Attached Thumbnails Attached Thumbnails IMG_1446.jpeg  

Similar Threads

  1. Homeworks Keypad Button Not Working
    By gaspower in forum General Discussion - Legacy HW
    Replies: 3
    Last Post: 01-19-2020, 01:18 PM
  2. Homeworks keypad update
    By am350z in forum General Discussion - HWQS
    Replies: 2
    Last Post: 06-17-2019, 06:36 PM
  3. Homeworks QS Keypad Compatibility
    By xyber007 in forum General Discussion - HWQS
    Replies: 1
    Last Post: 03-06-2018, 06:18 PM
  4. Combining zones to groups
    By franlog in forum 3rd-party Integration - HWQS
    Replies: 8
    Last Post: 07-19-2016, 06:04 PM
  5. Homeworks QS RF keypad problem
    By Peter Licht in forum Troubleshooting - HWQS
    Replies: 3
    Last Post: 11-08-2013, 05:00 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •