Thanks Thanks:  0
Likes Likes:  0
Results 1 to 2 of 2

Thread: Looking for Advice Wiring Caseta(PD-5ANS) in 3-Way

  1. #1
    Junior Member
    Join Date
    Dec 2022
    Posts
    1

    Question Looking for Advice Wiring Caseta(PD-5ANS) in 3-Way

    Hi Everyone,

    I would like to thank anyone that lends advice in advance as this is the first time using Caseta switch and I'm a little lost!

    I'm trying to wire a Caseta(PD-5ANS) in a 3 way configuration but the wiring diagram provided on Lutrons site and help videos have me a little confused and lost.

    I have 14/3 wire coming into there box(Black, White, Red, and Ground), the white wire on the 14/3 wire was connected to the different color screw so I tagged as described in the online help. I did try wiring the switch in however I left the blue wire off the back of the switch disconnected and wired it as follows:

    14/3 Wire - Caseta Switch
    White - Black
    Red - Red
    Ground - Green
    Black - White

    In this configuration the green led on the switch would light up, but the lights its controlling won't turn on. I did try switching it so white went to white, and black went to black this gave me the same results. I'm assuming all 5 wires off the back of the switch need to be hooked up to get control but I'm at a loss.

    Also if anyone knows if you can use the Caseta(PD-5ANS) in both locations to control the light?

    Again thanks in advance for taking the time to lend advice!

  2. #2
    Lutron Technical Support
    Join Date
    May 2022
    Posts
    23
    Hello,

    You are not able to use 2 PD-5ANS to control the same light. The options available are 1 PD-5ANS and a Mechanical Toggle Switch OR 1 PD-5ANS and a Pico Remote. You can view the wiring diagrams and installation guides for both applications in the Caseta Advanced Installation Guide Linked Below.

    https://webapiaw1proddat01st01.blob....structions.pdf

    Note: This control requires a neutral bundle to connect to. A Neutral wire would not have been connected to your previous control. Look for a bundle of 2 or more white or grey wires tied together and pushed back in the back of the wallbox. This is what your White Lead on the PD-5ANS should connect to. If you do not have neutrals available you can consider the PD-5WS-DV which does not require a neutral connection in the wallbox.

Similar Threads

  1. Caseta PD-5Ans to control gas lit sconce light
    By DEAN S in forum 3rd-party Integration - CAS
    Replies: 2
    Last Post: 10-07-2022, 01:01 AM
  2. Wiring Caseta D-5ANS-WH-R to fan LED light
    By Blueliberty in forum Troubleshooting - CAS
    Replies: 1
    Last Post: 01-15-2021, 11:33 AM
  3. Large Caseta Install - Advice Needed
    By Rickymerchant1 in forum General Discussion - CAS
    Replies: 14
    Last Post: 03-10-2019, 07:08 PM
  4. Advice re design and Caseta product selection
    By camner in forum Design Assistance - CAS
    Replies: 6
    Last Post: 02-16-2017, 10:01 AM
  5. Wiring Advice
    By Drake0508 in forum Troubleshooting - CAS
    Replies: 4
    Last Post: 04-03-2016, 03:54 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •