Thanks Thanks:  0
Likes Likes:  0
Dislikes Dislikes:  0
Results 1 to 6 of 6

Thread: Will Roller20 Universal Brackets fit Roller64 Shades?

  1. #1
    Junior Member
    Join Date
    Apr 2016
    Posts
    9

    Will Roller20 Universal Brackets fit Roller64 Shades?

    In the Roller Shade Bracket and Lineal Guide, it mentions Roller20 brackets are just a smaller version of roller 64 brackets.Will the Roller20 Universal Brackets also fit a Roller64 Shade if the diameter of the shade is less than 2.5" (Versus the larger 3.5" maximum diameter that Roller64 Shades can be)? Thanks!

  2. #2
    Senior Member
    Join Date
    Oct 2013
    Posts
    1,722
    Quote Originally Posted by cal122 View Post
    In the Roller Shade Bracket and Lineal Guide, it mentions Roller20 brackets are just a smaller version of roller 64 brackets.Will the Roller20 Universal Brackets also fit a Roller64 Shade if the diameter of the shade is less than 2.5" (Versus the larger 3.5" maximum diameter that Roller64 Shades can be)? Thanks!
    I couldn't find any dimensions on the brackets or the plastic mount on the rollers. They look the same size in a couple of drawings I saw but there were no dimensions.
    LED, Incorporated
    Raleigh, NC 27614

  3. #3
    Junior Member
    Join Date
    Apr 2016
    Posts
    9
    Thanks Randyc. I wasn't able to find the dimensions on the bracket parts that actually clips into the motor and tensioner sides. Have some window boxes that are very shallow (but the windows are wide so the 64 roller needs to be spec'd) I'm trying to keep flush. Looking at the fascia installation on 20 roller, it's 2.75" Wide (so roller64 without a lot of fabric length would fit fine if the bracket can actually clip in). Where as on the 64 fascia it would be 3.5" Wide.

  4. #4
    Senior Member
    Join Date
    Oct 2013
    Posts
    1,722
    Lutron realizes that we sometimes do things that are out of the box. Tech support will probably answer your question if you explain that you need the width they will probably get the answer.

    I did see the roller 64 universal bracket is 1.9375" wide. That is 5/16" wider than a bare roller 64 tube. You would have a little more than 1/8" of fabric on either side before you exceed the with of the 64 bracket. You may run into a minimum height issue.
    LED, Incorporated
    Raleigh, NC 27614

  5. #5
    Authorized Lutron Contributor
    Join Date
    May 2013
    Posts
    562
    A Roller 64 will not be able to fit in a Roller 20 bracket. The 2 fins on the Roller 20 bracket are too small for the drive of the Roller 64. They are similar in shape, but different sizes that are not inter-compatible.

  6. #6
    Junior Member
    Join Date
    Apr 2016
    Posts
    9
    Thank you!

Similar Threads

  1. Homeworks Illumination Control Somfy Universal RTS Interface II (URTSI II-16 Channel)
    By gaspower in forum 3rd-party Integration - Legacy HW
    Replies: 4
    Last Post: 06-22-2020, 11:00 AM
  2. Universal Remote Control & Caseta
    By Goneboating in forum 3rd-party Integration - CAS
    Replies: 16
    Last Post: 04-24-2019, 02:33 PM
  3. retrofitting Lutron motors into existing roller shades - Roller64
    By StephenP in forum General Discussion - Shades
    Replies: 2
    Last Post: 07-25-2018, 08:42 AM
  4. Universal Remote Control Dimmers and conversion to Radio Ra 2?
    By tonydutt in forum 3rd-party Integration - RA2
    Replies: 1
    Last Post: 11-24-2014, 09:20 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •