Thanks Thanks:  0
Likes Likes:  0
Results 1 to 5 of 5

Thread: new user blinking light

  1. #1
    Junior Member
    Join Date
    Apr 2020
    Posts
    2

    new user blinking light

    Had an electrician install Lutron smart bridge with Pico remote. Tonight I turned on an overhead light with the Pico remote. The light started to blink on and off. I turned it off and back on two times and it stopped. Is this a normal thing. I thot I had read something about a blinking light but can find the article. Anybody want to tackle this. Thanks

  2. #2
    Senior Member
    Join Date
    Oct 2013
    Posts
    2,049
    Quote Originally Posted by mrj 4732 View Post
    Had an electrician install Lutron smart bridge with Pico remote. Tonight I turned on an overhead light with the Pico remote. The light started to blink on and off. I turned it off and back on two times and it stopped. Is this a normal thing. I thot I had read something about a blinking light but can find the article. Anybody want to tackle this. Thanks
    The advanced instructions (link below) has a troubleshooting section that explains the blink codes.

    http://www.lutron.com/TechnicalDocum...structions.pdf
    Convergence Technologies Raleigh, North Carolina
    www.convergenceusa.com

  3. #3
    Senior Member
    Join Date
    May 2015
    Posts
    241
    I understand that his lights are blinking (flashing), not the LEDs on a switch.

  4. #4
    Senior Member
    Join Date
    Aug 2019
    Posts
    100
    Sounds like the lights being used may be on the incompatible side. May want to try lowering the high end trim on the dimmer by for which the directions start on page 67 of the following link. https://www.casetawireless.com/Docum...ced%20Inst.pdf If this does not work you may want to check the following link for compatible LED's. http://www.lutron.com/en-US/Pages/LE...atibility.aspx

  5. #5
    Junior Member
    Join Date
    Nov 2020
    Posts
    1
    Thank you, Matt H. I tried your advice to lower the high end trim on the dimmer. That made the light stop blinking. It seems like a crazy design to let me turn on the light too on, more than 100%, with no visual indication that I went too far. I had a newly installed Caseta Wireless that would blink / flash off a little over 1 second, then back on again. The light fixture was a dimmable Pixi Flatlight 1x2 size. It's not on Lutron's list of compatible LEDs because they only list light bulbs, but not light fixtures that incorporate LEDs. Here is a recording of the room light on and off times with 1-second resolution: ____ Elapsed time, Minutes:seconds 0:00 off 0:01 on 0:09 off 0:10 on 0:24 off 0:25 on 0:48 off 0:50 on 1:13 off 1:15 on 1:59 off 2:00 on 2:20 off 2:21 on 2:43 off 2:45 on 3:09 off 3:11 on

Similar Threads

  1. Replies: 6
    Last Post: 02-08-2019, 02:29 AM
  2. Serena Shade Not Working - Fast Blinking Red Light
    By TheRebel in forum Troubleshooting - Shades
    Replies: 7
    Last Post: 11-21-2018, 01:21 PM
  3. PD-5S-DV blinking red light of frustration
    By SoldierMed68W in forum Troubleshooting - CAS
    Replies: 1
    Last Post: 01-18-2018, 09:10 PM
  4. QS 8.1 Telnet Bug or User?
    By TechmoTim in forum General Discussion - HWQS
    Replies: 4
    Last Post: 02-18-2016, 10:36 PM
  5. End User Programming
    By Woodchopper in forum Programming - RA2
    Replies: 1
    Last Post: 04-25-2015, 06:47 PM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •