Thanks Thanks:  1
Likes Likes:  1
Dislikes Dislikes:  0
Results 1 to 4 of 4

Thread: ceiling motion sensor turns lights on full

  1. #1

    ceiling motion sensor turns lights on full

    I am looking to have a ceiling motion sensor that is manually paired with a Maestro Wireless elv dimmer turn the lights on at a preset level. At this moment when the wireless ceiling motion sensor trips the lights go on to full. How do i save the settings so the motion sensor turns the lights on at a preset level? Thanks for the help!

  2. Thanks Justin F. thanked for this post
    Likes Justin F. liked this post
  3. #2
    Senior Member
    Join Date
    Oct 2013
    Posts
    2,587
    I'm not 100% sure it will work but you can program the MRF dimmer turn on a preset level. It would depend if the sensor sends an "on" command or a "100%" command.
    Convergence Technologies Raleigh, North Carolina
    www.convergenceusa.com

  4. #3
    Authorized Lutron Contributor
    Join Date
    Sep 2018
    Posts
    87
    Hi AustinB.
    Thank you for your post! If you are using our Radio Powr Savr battery powered Occupancy Sensors like an LRF2-OCR2B-P-WH, you can set up a the occupancy sensor to turn the lights to a preset light level by doing the following:
    1.) Manually set the light level on the Maestro Wireless ELV dimmer using the up/down butons.
    2.) On the LRF2 Occupancy sensor, press and hold the light bulb button in for 5-6 seconds until the sensor lens starts to flash on/off and then release.

    The LRF2 Sensor will now turn the lighting load on to the preset light level when motion is detected with the lighting load off.

    Hope this info helps!

    -JustinF.

  5. #4
    Junior Member
    Join Date
    Aug 2020
    Posts
    2
    Hi Justin, When I do your steps it appears to initialize correctly, but the sensor continues to turn the lights on at 100%.
    I have an LRF2-OCR2B-P-WH sensor, Radio RA2 dimmer (RRD-PRO-LA), and a RadioRA2 Select controller.
    I set the preferred lighting level using up/down buttons.
    Pressing the dimmer button for 6 seconds causes all LEDs to blink.
    Pressing and holding the Light button on the sensor for 5-6 seconds causes the sensor light to blink several times and then stop.
    The Light button on the sensor then turns the lights on and off at 100%.
    The dimmer is not connected to the RA2 Select controller.
    I called tech support before I installed the sensor to confirm that it was compatible with the RA2 dimmers, but still not sure.

    Advice?
    Thanks

Similar Threads

  1. Lutron Caseta motion sensor lights
    By Squill in forum General Discussion - CAS
    Replies: 23
    Last Post: 05-08-2018, 10:12 AM
  2. Help with sensor that works with florescent ceiling lights 3 way
    By rsh916 in forum General Discussion - Controls
    Replies: 1
    Last Post: 10-09-2017, 03:52 PM
  3. Motion sensor, color lights, and Home integration
    By adiventure in forum 3rd-party Integration - CAS
    Replies: 2
    Last Post: 05-03-2017, 11:05 PM
  4. MA-LFQHW light swtich turns on fan on full brightness
    By teepee1232 in forum General Discussion - Controls
    Replies: 2
    Last Post: 10-09-2016, 09:14 AM
  5. Maestro Occupancy immediately turns off after detecting motion
    By Hayzen77 in forum Troubleshooting - Controls
    Replies: 4
    Last Post: 08-15-2015, 11:09 AM

Posting Permissions

  • You may not post new threads
  • You may not post replies
  • You may not post attachments
  • You may not edit your posts
  •