Devices keep droping out of activation in 10.1/10.2

Ok I'm way beyond tired of this problem.
Thought I posted this but look like it didn't post.

Three system.
System 1 & 2 are both 2 main with 130ish devices
System 3 is much smaller 1 main and 52 devices.

All transferred over Ethernet.
1 & 3 are 10.1
2 is 10.2

All will transfer fine at one point then next time drop devices.
Right now on system 2. Updated from 9.3-10. then from 10 to 10.2. Transferred and all good. Made changes then I get the pic attachedAttachment 518

All firewalls are off
Loads spread between both repeaters.
Re activating in a 2 main system sucks. Especially when your in a time crunch.

Sys 1 it happened multiple times with 3 of the 6 WPM

Are you kidding me!Attachment 519

Just re activated this and transferredAttachment 520 no problem. Made minor changes and then....................!!!!!!!!!!!!!!!!!!!!!!!!!! !!!!!!!!!!

So I found what's doing it. I think. Seams to be when I change a zone location on a WPM. 1st trans with no changes or problems 2nd changed zone name kitchen under cabs from kitchen to family. Trans and get the pic attached. 3rd changed Load type and trans no problem 4th changed load type and zone name back to original and trans no problem Attachment 521 I have support files but not see a way to post here. Will send to lutron email as WPM activation

Any ideas or replies?

Still having this problem. Changes on a WPM mean re-activation

Hi Mitch, have you sent in a Support File for us to review yet? Ideally we would like to see a support file from each system, but if you are going to be on 1 job site soon you can send that it to see what we can find. Then if we can pinpoint the cause of the issue you can check the other 2 sites for the same issue.

I did.
Looks like one went through the other was to big so I'll split it
I'll label each beginning with

Mitch E Re: Case #7197772 RadioRA 2 Support Issue WPM Activation

Did this just now at the office through the software only.
No repeaters hoked up.
Only thing I changed was load type on zone 1 of WPM 1
https://forums.lutron.com/attachment...ntid=534&stc=1https://forums.lutron.com/attachment...ntid=535&stc=1

Been doing some more testing. All files are now 10.4
On Fields, Munsch, and Mesic all I have to do is highlight the WPM1 and it looses the serial number. Made no changes.
Monkey around on the other WPM's with all sorts of changes and the serial number doesn't drop.
That's a bit odd because one of the pics above for mesic shows both WPM's didn't activate.

Me again. This is it. Gotta get back to work an pay the mortgage.
Found a little deeper clue.
Opened and converted a 9.2 file with 3 WPM that i know I never had problems with.
Monkey around and nothing dropped.
Converted to 10.4 and bingo.
Now for the deeper info. It happens on which ever one i look at first. Click on and gethttps://forums.lutron.com/attachment...ntid=536&stc=1 this pic. Not clicking or highlighting anything just
opening the WPM
Happens on all the files I sent you.

That is all.

Not giving up on this one.
Would love for someone to try the same thing and give me feed back or am I alone on this one?
Created a new file in 10.4. Everything in the equipment room. Main repeater, Connect bridge, standard keypad, WPM, 6CL. in that order.
Don't seam to be able to upload the file here.
Again, not connect to any systems. Only thing I'm connected to is WIFI.
Input 3 serial numbers from other jobs. WPM 01E30F19, Keypad 018FAC46, 6CL 018CB4A4
Obviously did not try to activate.
Go to Design and click on WPM, Done, and back to activation. WPM serial is still there.
Go back to design click on either the keypad or dimmer, Done. Stay in design and click on WPM, Done. Go to activation and WPM serial # is gonehttps://forums.lutron.com/attachment...ntid=538&stc=1https://forums.lutron.com/attachment...ntid=539&stc=1https://forums.lutron.com/attachment...ntid=540&stc=1

Did the exact same thing in 9.3 with no problems
In 10.0 all I had to do was click on the WPM in design and S# was gone. With or without the connect bridge

Hi MitchE
If I had a Ra2 file with WPM activated in it, I'd try it. I'm going to assume based on your thorough testing that you've found a bug in the Ra2 software. Hope it's resolved soon.

That's the kicker digi1. I created a new file, non activated, never saw a repeater and this happens.
Anyone with software can try this to confirm.