Activity Stream - Lutron Support Community

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

Today, 08:24 PM

Bakaboy1234 started a thread Extracting project file error in Programming - RA2

So my lutron system has been operating well for almost 5 years, but a couple of days back the keypads randomly stopped working. Some keypads just...

0 replies | 6 view(s)

Today, 06:51 PM

Brian. replied to a thread DVTV and PP-DV, no dimming in Troubleshooting - Controls

Just for follow-up and closure: It wasn't the switch or the powerpack. It also wasn't the lights/drivers. It was the Electricians (and me). ...

4 replies | 292 view(s)

Today, 06:12 PM

DeeMX started a thread Homeworks 8 processor problem to access in Troubleshooting - Legacy HW

Hello Can't get access to Homeworks 8 processor via web browser. check attachment Thanks

0 replies | 4 view(s)

Today, 05:53 PM

Kyle L. replied to a thread Lutron Diva - ceiling fan hum increases with power in Troubleshooting - Controls

Good afternoon. The DVCL-153P is a dimmer that is designed to control lighting loads, not fan motors. We would recommend using the DVFSQ-F for the...

1 replies | 9 view(s)

Today, 05:11 PM

Kingfisher started a thread Occupancy Sensor not responding to On (but Off works) w/ conditional. Possible bug? in Troubleshooting - HWQS

I have two identical rooms each with it's own sensor and programming. One room works fine, the other one doesn't. I can't figure it out for the life...

0 replies | 6 view(s)

Today, 04:30 PM

jab1000 started a thread Lutron Diva - ceiling fan hum increases with power in Troubleshooting - Controls

I have a Craftmade ceiling fan (Craftmade TEA52SB4-UCI) which I personally just installed -- our bedroom has 2 separate switches as well. One wired...

1 replies | 9 view(s)

Today, 04:30 PM

Jonathan K. replied to a thread DVRF-6L Diva Dimmer - no status LEDs in Troubleshooting - CAS

I'm glad you were able to identify and remedy the issue. The minimum load of the DVRF-6L is 25W of incandescent/halogen load or 1 - 2 compatible...

3 replies | 19 view(s)

Today, 04:19 PM

HardCoal99 replied to a thread DVRF-6L Diva Dimmer - no status LEDs in Troubleshooting - CAS

It’s a single pole application, and there is no manufacturer markings on the lighting. I started troubleshooting my hunch that there wasn’t...

3 replies | 19 view(s)

Today, 03:22 PM

Jonathan K. replied to a thread DVRF-6L Diva Dimmer - no status LEDs in Troubleshooting - CAS

Do you have the make and model of the under cabinet LED lights? Also, is the dimmer installed in a single-pole or is it part of a 3-way or 4-way?

3 replies | 19 view(s)

Today, 03:13 PM

HardCoal99 started a thread DVRF-6L Diva Dimmer - no status LEDs in Troubleshooting - CAS

Just bought three DVRF-6L dimmers for my kitchen. One switch is for some under cabinet LED lighting. When I turn the breaker on, that switch will...

3 replies | 19 view(s)

Today, 01:11 PM

mfrymyer started a thread Best Device to Control Fan Speed and On/Off in General Discussion - CAS

Hi All, I'm new to the Lutron Caseta family. I just installed a bunch of smart switches to my house and some of them are the original fan...

0 replies | 14 view(s)

Today, 01:08 PM

mfrymyer started a thread Best Device to Control Fan Speed and On/Off in Design Assistance - CAS

Hi All, I'm new to the Lutron Caseta family. I just installed a bunch of smart switches to my house and some of them are the original fan...

0 replies | 14 view(s)

Today, 12:05 PM

hrevete replied to a thread factory reset an rr-proc3 processor in Troubleshooting - RA3

I didn't know exactly those steps, the manual doesn't indicate them, I figured it was because of the button on the front, thanks for telling me how...

2 replies | 49 view(s)

Today, 12:02 PM

hrevete replied to a thread Sunnata RRST-8ANS is not in toolbox in Troubleshooting - RA3

Hello, I know the reason why I didn't have the switch in the toolbox, is that when I created the new project I put Venezuela as the country, and they...

2 replies | 41 view(s)

Today, 11:02 AM

mgill replied to a thread New PD-FSQN Install in Troubleshooting - CAS

Thanks for this. Going through the list I think I'm meeting every requirement. Here is the fan Ive installed: Minka Group® :: BRANDS ::...

4 replies | 184 view(s)

Today, 10:04 AM

Kyle S replied to a thread factory reset an rr-proc3 processor in Troubleshooting - RA3

Hello, Follow these steps to reset your processor -Unplug your processor for 30 seconds. (The default must be done within 30 minutes of a power...

2 replies | 49 view(s)

Today, 09:52 AM

Kyle S replied to a thread Sunnata RRST-8ANS is not in toolbox in Troubleshooting - RA3

Hello, To add the RRST-8ANS follow these steps. Go to the design tab and click edit toolbox. In the search bar enter RRST-8ANS and add the...

2 replies | 41 view(s)