Activity Stream - Lutron Support Community

Sort By	Time	Show
Recent Recent Popular Popular	Anytime Anytime Last 24 Hours Last 24 Hours Last 7 Days Last 7 Days Last 30 Days Last 30 Days	All All Photos Photos Forum Forums

Yesterday, 03:59 PM

hrevete started a thread factory reset an rr-proc3 processor in Troubleshooting - RA3

Hello. How to factory reset a rr-proc3 processor?

2 replies | 37 view(s)

Today, 03:13 PM

HardCoal99 started a thread DVRF-6L Diva Dimmer - no status LEDs in Troubleshooting - CAS

Just bought three DVRF-6L dimmers for my kitchen. One switch is for some under cabinet LED lighting. When I turn the breaker on, that switch will...

1 replies | 7 view(s)

Yesterday, 03:59 PM

bigwave started a thread Need stacked paddle switch for 1 garbage disposer and 1 led lights in Design Assistance - Controls

I need a single gang stacked paddle switch to accommodate a garbage disposer and a string of LED under counter lights. One that looks similar to the...

0 replies | 29 view(s)

Today, 01:08 PM

mfrymyer started a thread Best Device to Control Fan Speed and On/Off in Design Assistance - CAS

Hi All, I'm new to the Lutron Caseta family. I just installed a bunch of smart switches to my house and some of them are the original fan...

0 replies | 9 view(s)

Today, 01:11 PM

mfrymyer started a thread Best Device to Control Fan Speed and On/Off in General Discussion - CAS

Hi All, I'm new to the Lutron Caseta family. I just installed a bunch of smart switches to my house and some of them are the original fan...

0 replies | 8 view(s)

Today, 03:22 PM

Jonathan K. replied to a thread DVRF-6L Diva Dimmer - no status LEDs in Troubleshooting - CAS

Do you have the make and model of the under cabinet LED lights? Also, is the dimmer installed in a single-pole or is it part of a 3-way or 4-way?

1 replies | 7 view(s)

Today, 12:05 PM

hrevete replied to a thread factory reset an rr-proc3 processor in Troubleshooting - RA3

I didn't know exactly those steps, the manual doesn't indicate them, I figured it was because of the button on the front, thanks for telling me how...

2 replies | 37 view(s)

Today, 12:02 PM

hrevete replied to a thread Sunnata RRST-8ANS is not in toolbox in Troubleshooting - RA3

Hello, I know the reason why I didn't have the switch in the toolbox, is that when I created the new project I put Venezuela as the country, and they...

2 replies | 36 view(s)

Today, 11:02 AM

mgill replied to a thread New PD-FSQN Install in Troubleshooting - CAS

Thanks for this. Going through the list I think I'm meeting every requirement. Here is the fan Ive installed: Minka Group® :: BRANDS ::...

4 replies | 175 view(s)

Today, 10:04 AM

Kyle S replied to a thread factory reset an rr-proc3 processor in Troubleshooting - RA3

Hello, Follow these steps to reset your processor -Unplug your processor for 30 seconds. (The default must be done within 30 minutes of a power...

2 replies | 37 view(s)

Today, 09:52 AM

Kyle S replied to a thread Sunnata RRST-8ANS is not in toolbox in Troubleshooting - RA3

Hello, To add the RRST-8ANS follow these steps. Go to the design tab and click edit toolbox. In the search bar enter RRST-8ANS and add the...

2 replies | 36 view(s)

Yesterday, 04:47 PM

SparkyCoog replied to a thread System and dimmers unresponsive after alarm system(CC) was triggered in Troubleshooting - RA2

Well,I don't go to this customer's house often and already did one free service call. If it happens again, what do I need to pull when I contact...

3 replies | 149 view(s)

Yesterday, 04:24 PM

Kenneth P. replied to a thread Installation Question - First PD-6ANS-WH in Troubleshooting - CAS

Hello, It is possible that this could be switching on the neutral instead of on the hot. If this is the case, the best recommendation would be to...

1 replies | 102 view(s)